www.ccna4u.org
CCNA3 Final – 04 March 2010
(Thanks dip see)

Welcome and get lastest CCNA Exploration 4.0 Questions and answers
Email: quocvuong.it@gmail.com
Website:
www.ccna4u.org
www.ccna4u.net
www.ccna4u.info

1
Which value determines if a switch becomes the central point of reference in the spanning tree topology?
lowest bridge ID
highest revision number
lowest numeric IP address
highest numeric MAC address
2
Refer to the exhibit. What is the purpose of the configuration commands that are shown?
to activate port Fa0/10
to make the port a member of VLAN 30
to activate port security on port Fa0/10
to add VLAN 30 to the trunk that is connected to port Fa0/10
3
Refer to the exhibit. What would happen if the network administrator moved the network cable of Host A from interface Fa0/1 to Fa0/switch SW1?
Host A remains a member of VLAN 10, because the router is routing traffic between VLANs.
Host A is no longer a member of VLAN 10, because port Fa0/3 has been manually assigned to VLAN 30.
Host A remains a member of VLAN 10, because the switch provides dynamic VLAN assignment for the port.
Host A maintains connectivity to all members of VLAN 10, because it is connected to the same physical network.
Host A is no longer a member of VLAN 10, but because port Fa0/3 was unused, it is now a member of VLAN 1.
4
Which device or devices should have the Spanning Tree Protocol enabled to prevent host traffic from creating a broadcast storm?
Core_S1
Access_S2 and Access_S3
Core_S1, Access_S2, and Access_S3
Core_S1, Access_S2, Access_S3, and R1
5
Refer to the exhibit. The hosts connected to switch SW1 are not able to communicate with the hosts in the same VLANs connected switch SW2. What should be done to fix the problem?
Configure VLANs with different VLAN IDs on switch SW2.
Reconfigure the trunk port on switch SW2 with static trunk configuration.
Introduce a Layer 3 device or a switch with Layer 3 capability in the topology.
Apply IP addresses that are in the same subnet to the interfaces used to connect SW1 and SW2.
6
Refer to the exhibit. The Layer 2 switching design that is shown has been implemented in a campus environment that is using Spanning
Tree Protocol. All inter-switch links that are shown are trunks. Whenever an inter-switch link fails, the network takes nearly a minute completely converge. How can the convergence time be reduced?
Increase the capacity of the distribution and core trunk links to 10 Gb/s.
Add a trunk link that directly connects D1 and D2.
Use Layer 3 switching on the core switch.
Implement Rapid Spanning Tree Protocol.
7 What will be the effect of the command S1# copy system:running-config 172.16.2.155/tokyo-config?
The IOS will be copied to the TFTP server.
The configuration file named tokyo-config will overwrite the startup configuration file on S1.
The running configuration file on S1 will be saved via TFTP to a file named tokyo-config.
The contents of NVRAM on S1 will become the startup configuration file on the tokyo switch.
8
Refer to the exhibit. What does the term DYNAMIC indicate in the output that is shown?
This entry can only be removed from the MAC address table by a network administrator.
When forwarding a frame to the device with address 0060.5c5b.cd23, the switch does not have to perform a lookup to determine
the final destination port.
Only the device with MAC address 0060.5c5b.cd23 will be allowed to connect to port Fa0/18.
The switch learned this MAC address from the source address in a frame received on Fa0/18.9 Which two statements are correct about wireless infrastructure components? (Choose two.)
An AP converts the TCP/IP data packets from their 802.11 frame encapsulation format to the 802.3 Ethernet frame format on the
wired Ethernet network.
A wireless AP does not require any physical connection to allow wireless clients to access the Internet.
An AP is a layer 2 device, similar to a switch, that provides dedicated bandwidth to each connected wireless host.
Collisions do not occur between wireless NICs and APs.
The wireless router performs the roles of AP and router.
10
Which service should be disabled on a Cisco switch or router to prevent packet sniffers from capturing information about the device?
SSH
VTP
CDP
SNMP
11
Refer to the exhibit. Hosts A and B, connected to hub HB1, attempt to transmit a frame at the same time but a collision occurs. Which
hosts will receive the collision jamming signal?
only hosts A and B
only hosts A, B, and C
only hosts A, B, C, and D
only hosts A, B, C, and E
12
What are three benefits of employing a hierarchical network design? (Choose three.)
Hierarchically designed networks can more easily be expanded to suit future needs.
Hierarchical design models enhance existing bandwidth through the use of link aggregation.
The hierarchical model allows for specialized functionality at each layer, simplifying device management.Use of a hierarchical design allows replacement of redundant devices with high-capacity network equipment.
A hierarchical design uses firewalls instead of complicated port-based and distribution layer security policies.
The hierarchical model allows the use of high-performance switches at all design layers, thus allowing for a fully-meshed topology.
13 A network administrator implements inter-VLAN routing by configuring subinterfaces on a router. What is one important fact that must considered?
The physical interface must have an IP address configured.
The subinterface numbers must match the VLAN ID number.
The no shutdown command must be issued on each subinterface.
The IP address of each router subinterface must be used as the default gateway for hosts on the corresponding VLAN.
14
Which type of frame contains information that is used in the election of the spanning tree root bridge?
BID
LSA
LSU
BPDU
15
Refer to the exhibit. Each switch is shown with its MAC address. Which switch will be elected as the spanning-tree root bridge if the
switches are configured with their default priority values?
switch A
switch B
switch C
switch D
switch E
switch F
Close Window
Assessment System
1. Assessment Selection 2. Assessment Settings 3. Take Assessment
Take Assessment – ESwitching Final Exam – CCNA Exploration: LAN Switching and
Wireless (Version 4.0)
Time Remaining:
16
Refer to the exhibit. What will happen when frames with a source address other than 0019.d2e4.d9f7 enters interface Fa0/24?
Fa0/24 will become error-disabled.
The incoming frames will be dropped.
The Fa0/24 port LED will be turned off.
The security violation count will be incremented.
17
Refer to the exhibit. The network administrator has just added VLAN 50 to Switch1 and Switch2. Hosts A, B, C, and D are correctly
configured with IP addresses in the subnet range for VLAN 50. Host A can communicate with host B, but cannot communicate with C or host D. What is the cause of this problem?
There is a native VLAN mismatch.
The Fa0/11 interface of Switch1 is not configured as a trunk.
The link between Switch1 and Switch2 is up but not trunked.
VLAN 50 is not allowed on the trunk link between Switch1 and Switch2.
18
Refer to the exhibit. A network administrator enters the displayed commands to configure VLAN 30. What is the result of running these
commands?
VLAN 30 will be added to S1, S2, and S3, but not to S4.
VLAN 30 will be pruned from the VLAN database of S3.
VLAN 30 will be added to the VLAN database of S3 but will not be propagated to S4, S2 or S1.
VLAN 30 will not be added to the VLAN database of S3 and an error message will be displayed.
19
Refer to the exhibit. R1 is configured for traditional inter-VLAN routing. R1 can ping computer 3 but cannot ping computer 1. What is possible cause for this failure?
S1 port Fa0/11 is in the wrong VLAN.
R1 does not have an active routing protocol.
The IP address of computer 1 is in the wrong logical network.
Router interface Fa0/0 has the wrong trunk encapsulation type configured.
20
Refer to the exhibit. How does SW1 manage traffic coming from Host A?
SW1 drops the traffic because it is untagged.
SW1 leaves the traffic untagged and forwards it over the trunk.
SW1 tags the traffic with the lowest VLAN ID value and forwards it over the trunk link.
SW1 encapsulates the traffic with 802.1Q encapsulation and forwards it over the trunk link.
21
Refer to the exhibit. What will allow a host on VLAN 40 on switch X to communicate with a host in VLAN 40 on switch Y?
QoS
routing
trunking
VPN
22 When implementing a router-on-a-stick, what must be configured on the router to ensure connectivity between different VLANs?
subinterfaces
routing protocol
switched virtual circuits
dynamic trunking protocol
23
Refer to the exhibit. Users complain that they do not have connectivity to the web server that is connected to SW1. What should be to remedy the problem?
Allow all VLANs on the trunk link.
Configure VLAN 100 as the native VLAN for SW1.
Configure the trunk port in trunk mode on SW1.
Attach the web server to a router and configure inter-VLAN routing.
24 Which method establishes an administrative connection for configuring the Linksys WRT300N wireless access point?
Associate with the access point and then open a HyperTerminal session with the access point.
Physically connect to the access point and then reboot the computer to launch the configuration software.
From a computer in the same IP subnet as the access point, enter the default IP address of the access point in a web browser.
Modify the TCP/IP properties of the computer connected to the access point so that it exists on the same network, and then reboot
your computer to establish a connection.
25
Company policy requires disabling the command history buffer on network devices. An administrator enters terminal no history size
the command prompt on a Cisco Catalyst switch and receives no error messages back, but the command history buffer is still available.

What is the problem?
The command contained a syntax error.
The Cisco IOS version does not support disabling the command history buffer.
The command history can only be disabled on a router, not a switch.
The size parameter reset the default buffer size but did not disable access to the buffer.26
Refer to the exhibit. What does “FORWARDING” mean in the command output shown?
The switch is sending and receiving data frames.The switch is receiving BPDUs, but not sending data frames.
The switch is participating in an election process by forwarding the BPDUs it receives.
The switch is receiving BPDUs and populating the MAC address table, but not sending data.
27
Refer to the exhibit. Which switch will be elected as the root bridge of the spanning tree topology?
Cat-A
Cat-B
Cat-C
Cat-D
28
Refer to the exhibit. A new host needs to be connected to VLAN 1. Which IP address should be assigned to this new host?
192.168.1.11 /28
192.168.1.22 /28192.168.1.33 /28
192.168.1.44 /28
192.168.1.55 /28
29
Refer to the exhibit. All trunk links are operational and all VLANs are allowed on all trunk links. An ARP request is sent by computer Which device or devices will receive this message?
only computer 4
computer 3 and RTR-Acomputer 4 and RTR-A
computer 1, computer 2, computer 4, and RTR-A
computer 1, computer 2, computer 3, computer 4, and RTR-A
all of the computers and the router
30
Refer to the exhibit. The switches in the exhibit have VTP pruning enabled. What will be pruned in the VTP advertisements from switch
ST-C to switch ST-1?
VLAN 30
VLAN 20 and VLAN 30
VLAN 1, VLAN 20, and VLAN 30
VLAN 2 through VLAN 29, and VLAN 31 through VLAN 1000
Showing 2 of 4
Close Window
All contents copyright 1992-2009 Cisco Systems, Inc. Privacy Statement and Trademarks.
Close Window
Assessment System
1. Assessment Selection 2. Assessment Settings 3. Take Assessment
Take Assessment – ESwitching Final Exam – CCNA Exploration: LAN Switching and
Wireless (Version 4.0)
Time Remaining:
31
Refer to the exhibit. An administrator documented the output of a CAM table from an Ethernet switch as shown. What action will the
switch take when it receives the frame shown at the bottom of the exhibit?
discard the frame
forward the frame out port 2
forward the frame out port 3
forward the frame out all ports
forward the frame out all ports except port 3
add station 00-00-3D-1F-11-05 to port 2 in the forwarding table
32
What are two requirements for configuring inter-VLAN routing using the router-on-a-stick model? (Choose two.)
Each subinterface should be configured with its own IP address, subnet mask, and unique VLAN assignment.
The physical interface of the router must be connected to a trunk link on the adjacent switch.The number of physical interfaces on the router should match the number of VLANs.
Different static VLANs should be assigned to different interfaces of the router.
The router should be configured as the VTP server.
33
Refer to the exhibit. The switch VTY lines have been properly configured, but PC1 is unable to remotely manage the switch. How can
this problem be resolved?
Configure the Fa0/1 interface of the switch in trunk mode.
Configure a default gateway on the switch.Configure the native VLAN on the switch.
Configure the Fa0/1 interface of the switch to allow all VLANs.
34
Refer to the exhibit. After entering the commands in the exhibit, the administrator receives a “password required, but none set” message
when attempting to connect to S1. What is the problem?
The enable secret password was not set.
S1 does not have login configured on the vty lines.
S1 does not have a password configured for the vty lines.The crypto key is not properly configured to generate passwords.
The VLAN1 interface has not be enabled with the no shutdown command.
35
Refer to the exhibit. After the listed commands are entered into router R1 and switch S1, the administrator enters the show interface
fa0/1 trunk and gets the results shown. What is the likely problem?
The trunk is established, but no VLANs have been configured to use it.
The router is missing the dynamic trunking protocol statements necessary to form a trunk.
The trunk has not been established because the router does not support dynamic trunking protocol.The router, the switch, or both must be configured with the dynamic desirable option for dynamic trunking protocol to establish trunk.
36
Which parameter is used to uniquely identify one wireless network from another?
SSIDOFDM
WEP
DSSS
37
Refer to the exhibit. Switch SW2 has been newly purchased and added to the network. What configuration should be applied to SW2 that it participates in the same VTP domain as switch SW1, receives VLAN information from SW1, and synchronizes VLAN information?
Disable VTP pruning on SW2.
Configure SW2 in VTP transparent mode.
Configure SW2 with the VTP domain password.
Configure SW2 as a VTP server with a higher revision number.
38
Refer to the exhibit. In what two ways will the router handle VLAN traffic that is received on the trunk? (Choose two.)
Traffic to VLAN 1 received by the router interface Fa0/0 will be dropped by the router.Because interface Fa0/0 requires an IP address, the router will not be able to route between the VLANs.
Packets that are received from network 192.168.20.0 /24 will be handled by subinterface Fa0/0.20.The router will use subinterface MAC addresses to identify the VLAN traffic that is received on the physical interface.
The router will continue to process traffic from the attached VLANs even if the physical interface goes down.
http://www.ccna4u.org 39
In which mode is a VTP switch operating if it does not allow for the creation of local VLANs but it does accept VLAN updates from other
switches in the same domain?
client
root
server
transparent
40
Which configuration changes will increment the configuration revision number on the VTP server?
configuring trunk links on the VTP server
configuring or changing the VTP password
configuring or changing the VTP domain name
configuring or changing the VTP version number
configuring or deleting a VLAN or creating a VLAN name
41
Refer to the exhibit. Switches S2 and S3 are properly connected using an ethernet cable. A network administrator has configured both
switches with VTP, but S3 is unable to propagate VLANs to S2. What could be the reason for this?
The VTP configuration revision is different on both switches.
The VTP domains are different on both switches.
VTP pruning is disabled.
VTP v2 is disabled.
42
Refer to the exhibit. What is true of the configuration of switch S1?
Only VLAN 99 will be allowed to use the trunk links.
Switch ports Fa0/1 and Fa0/3 are configured with a standard trunking protocol.
Switch ports Fa0/1 and Fa0/3 should be configured as access ports to allow data from multiple VLANs to access switch S1.
The switch negotiated trunk links for interfaces Fa0/1 and Fa0/3 because all connected interfaces have been configured with the
switchport mode dynamic auto command.
43
What is an efficient and cost effective way to minimize the frequency and effects of broadcast storms on an Ethernet LAN?
Connect each PC directly to a router port.
Use access control lists to filter broadcasts from the network.
Divide the computers into separate VLANs on the existing switches.
Divide the computers into separate workgroups using different physical switches.
44
Refer to the exhibit. The configuration steps that are listed in the exhibit have been entered in switch S1 via the console. Subsequent
attempts to telnet to the switch are not successful. What is causing the problem?
The switch must be configured with SSH version 1.
The transport input command must specify Telnet access.
The RSA keys must be returned to zero before SSH will permit Telnet access.
The ip domain-name command must also be entered in line configuration mode for the vty lines.
45 Why is it important that the network administrator consider the spanning-tree network diameter when choosing the root bridge?
The network diameter limitation is 9.
BPDUs may be discarded because of expiring timers.
The cabling distance between the switches is 100 meters.
The network diameter must be set to the number of meters of the cable between the root bridge and its farthest connected switch.
Showing 3 of 4
Close Window

Assessment System
1. Assessment Selection 2. Assessment Settings 3. Take Assessment
Take Assessment – ESwitching Final Exam – CCNA Exploration: LAN Switching and
Wireless (Version 4.0)
Time Remaining:
46
Refer to the exhibit. The commands are entered into switch SW1 as shown, and an 802.1q trunk is successfully established. How does
switch SW1 handle the untagged traffic that is destined for the trunk?
SW1 will drop all untagged traffic.
SW1 will send all untagged traffic to VLAN 1.
SW1 will send all untagged traffic to VLAN 25.
SW1 will send untagged traffic to all VLANs that are configured on the trunk.
47
Refer to the exhibit. All hosts are in listen mode. Host 1 and Host 4 both transmit data at the same time. How do the hosts respond the network? (Choose two.)
After the end of the jam signal, a backoff algorithm is invoked.
Hosts 1 and 4 are operating full duplex so no collision will exist.
The hub will block the port connected to Host 4 to prevent a collision.
Hosts 1 and 4 are assigned shorter backoff values to provide them priority to access the media.
If a host has data to transmit after the backoff period of that host, the host checks to determine if the line is idle before transmitting.
48
Refer to the exhibit. Hosts PC_A and PC_B send traffic simultaneously, and the frames from the transmitting stations collide. What last device to receive the collision?
hub HB1
switch SW1
router R1
switch SW2
router R2
switch SW4
49
What provides an authentication mechanism for 802.11-based wireless networks?
DSSS
OFDM
SSID
WPA
50 What are two benefits of the IEEE 802.11n standard over the IEEE 802.11G? (Choose two.)
requires less equipment
provides improved range
permits increased data rates
has a single-input and a single-output
needs no hardware upgrade for compatibility
51
Refer to the exhibit. Users A and B are reporting intermittent connectivity problems. Pre-installation surveys showed strong signal
strength from the AP locations to the client locations. Outside electrical interference has been eliminated. What will fix the problem?
Relocate the APs closer to each other.
Increase the distance between the clients.
Change the channel on AP-B to 6 or 11.
Place AP-A and AP-B on the same wireless channel.
52 Why is MAC address filtering considered a poor choice in securing a WLAN?
Available bandwidth is reduced.
MAC addresses are easily spoofed.
APs are more susceptible to DoS attacks.
The payload encryption is easily broken.
Showing 4 of 4
Close Window http://www.ccna4u.org

Your contribution will help keep this site updated!

Expect minimum percentage: 94.8%

1. Refer to the exhibit. All routers are running the same routing protocol. Based on the exhibit and its displayed commands, which statement is true?
ans:
The link to the ISP is not advertised by the routing protocol process.

2. Refer to the exhibit. While trying to diagnose a routing problem in the network, the network administrator runs the debug ip rip command. What can be determined from the output of this command?
ans:
The router will be unable to ping 192.168.1.2.

3. Refer to the exhibit. Two routers are unable to establish an adjacency. What is the possible cause for this?
ans:
The hello and dead intervals are different on the two routers.

4. Refer to the exhibit. Routers R1 and R2 are directly connected via their serial interfaces and are both running the EIGRP routing protocol. R1 and R2 can ping the directly connected serial interface of their neighbor, but they cannot form an EIGRP neighbor adjacency.
ans:
Configure both routers with the same EIGRP process ID.

5. Refer to the exhibit. Routers R1 and R3 use different routing protocols with default administrative distance values. All devices are properly configured and the destination network is advertised by both protocols.

Which path will be used to transmit the data packets from PC1 to PC2?
ans:
The packets will travel via R2-R1.

6. Refer to the exhibit. What is the meaning of the highlighted value 2?
ans:
It is the number of hops between R2 and the 192.168.8.0/24 network.

7. What is the function of the OSPF LSR packet?
ans:
It is used by the receiving routers to request more information about any entry in the DBD.

8. Which three statements are true regarding the encapsulation and de-encapsulation of packets when traveling through a router? (Choose three.)
ans:
The router modifies the TTL field, decrementing it by one.
The router maintains the same source and destination IP.
The router changes the source physical address to the physical address of the exit interface.

9. Refer to the exhibit. The routers are properly configured using a dynamic routing protocol with default settings, and the network is fully converged. Router A is forwarding data to router E. Which statement is true about the routing path?
ans:
If the network uses the RIP protocol, router A will determine that all paths have equal cost.

10. Refer to the exhibit. A network administrator has run the show interface command. The output of this command is displayed. What is the first step that is required to make this interface operational?
ans:
Issue the no shutdown command on the interface.

11. Refer to the exhibit. Both routers are using the RIPv2 routing protocol and static routes are undefined. R1 can ping 192.168.2.1 and 10.1.1.2, but is unable to ping 192.168.4.1.

What is the reason for the ping failure?
ans:
The 192.168.4.0 network is not included in the RIP configuration of R2.

12. Refer to the exhibit. R2 is configured correctly. The network administrator has configured R1 as shown. Which two facts are true about the forwarding of route information by R1? (Choose two.)
ans:
R1 will forward the route information for subnet 192.168.100.0/30.
R1 will forward the route information with an administrative distance set to 50.

13. Refer to the exhibit. The network has three connected routers: R1, R2, and R3. The routes of all three routers are displayed. All routers are operational and pings are not blocked on this network.

Which ping will fail?
ans:
from R1 to 192.168.3.1

14. Refer to the exhibit. A network administrator has configured R1 as shown, and all interfaces are functioning correctly. A ping from R1 to 172.16.1.1 fails. What could be the cause of this problem?
ans:
The default route is configured incorrectly.

15. Which two router component and operation pair are correctly described? (Choose two.)
ans:
NVRAM – stores the configuration file
POST – runs diagnostics on hardware modules

16. A network administrator uses the RIP routing protocol to implement routing within an autonomous system. What are two characteristics of this protocol? (Choose two.)
ans:
It uses the Bellman-Ford algorithm to determine the best path.
It periodically sends complete routing tables to all connected devices.

17. Refer to the exhibit. Host A is unable to access the Internet. What is the reason for this?
ans:
The Fa0/1 interfaces of the two routers are configured for different subnets.

18. Refer to the exhibit. All interfaces are addressed and functioning correctly. The network administrator runs the tracert command on host A. Which two facts could be responsible for the output of this command? (Choose two.)
ans:
The entry for 192.168.2.0/24 is missing from the routing table of R1.
The entry for 192.168.2.0/24 is missing from the routing table of R2.

19. What are two functions of a router? (Choose two.)
ans:
It forwards data packets toward their destination.
It acts as an intersection between multiple IP networks.

20. Which statement is true about the RIPv1 protocol?
ans:
It excludes subnet information from the routing updates.

21. Refer to the exhibit. To implement the RIPv2 protocol, the network administrator runs the commands as displayed. However, the show ip protocol command fails to display any output. How can the administrator solve the problem that is indicated by the lack of output from this command?
ans:
Specify the network for which RIP routing has to be enabled.

22. Refer to the exhibit. An administrator is adding a new subnet of 50 hosts to R3. Which subnet address should be used for the new subnet that provides enough addresses while wasting a minimum of addresses?
ans:
192.168.1.64/26

23. Refer to the exhibit. R1 and R2 are unable to establish an adjacency. What two configuration changes will correct the problem? (Choose two.)
ans:
Configure the routers in the same area.
Match the hello and dead timers on both routers.

24. What two routing protocols use a hierarchal network topology? (Choose two.)
ans:
IS-IS
OSPF

25. Refer to the exhibit. Router R2 is configured properly and all interfaces are functional. Router R1 has been installed recently. Host A is unable to ping host B.

Which procedure can resolve this problem?
ans:
Configure a static route on R1 using the IP address of S0/0/0 on R2.

26. All routers in a network are configured in a single OSPF area with the same priority value. No loopback interface has been set on any of the routers. Which secondary value will the routers use to determine the router ID?
ans:
The highest IP address among the active interfaces will be used.

27. Which two statements are true for link-state routing protocols? (Choose two.)
ans:
Routers that run a link-state protocol can establish a complete topology of the network.
The shortest path first algorithm is used.

28. A router boots and enters setup mode. What is the reason for this?
ans:
The configuration file is missing from NVRAM.

29. Refer to the exhibit. The show cdp neighbors command was run at R1. Which two facts about the newly detected device can be determined from the output? (Choose two.)
ans:
ABCD is a router that is connected to R1.
The device is connected at the Serial0/0/1 interface of R1.

30. What are two tasks that must be completed before two routers can use OSPF to form a neighbor adjacency? (Choose two.)
ans:
The routers must agree on the network type.
The routers must use the same dead interval.

31. Refer to the exhibit. A ping between host A and host B is successful, but pings from host A to operational hosts on the Internet fail. What is the reason for this problem?
ans:
One of the default routes is configured incorrectly.

32. What two routing protocols will produce a shortest path first tree? (Choose two.)
ans:
IS-IS
OSPF

33. Refer to the exhibit. Which three statements are true of the routing table for Router1? (Choose three.)
ans:
The AD of EIGRP routes has been manually changed to a value other than the default value.
Router1 is running both the EIGRP and OSPF routing process.
No default route has been configured.

34. Refer to the exhibit. What action will R2 take for a packet that is destined for 192.168.2.0?
ans:
It will forward the packet to R1.

35. Refer to the exhibit. A router learns a route to the 192.168.6.0 network, as shown in the output of the show ip rip database command. However, upon running the show ip route command, the network administrator sees that the router has installed a different route to the 192.168.6.0 network learned via EIGRP. What could be the reason for the missing RIP route?
ans:
Compared to RIP, EIGRP has a lower administrative distance.

36. Which two components are used to determine the router ID in the configuration of the OSPF routing process? (Choose two.)
ans:
the highest IP address of any logical interface
the highest IP address of any physical interface

37. Refer to the exhibit. A network administrator is accessing router R1 from the console port. Once the administrator is connected to the router, which password should the administrator enter at the R1> prompt to access the privileged EXEC mode?
ans:
Cisco789

38. Which routing protocol maintains a topology table separate from the routing table?
ans:
EIGRP

39. Refer to the exhibit. Which summarization should R1 use to advertise its networks to R2?
ans:
192.168.0.0/22

40. Refer to the exhibit. All routers are running RIPv1. The two networks 10.1.1.0/29 and 10.1.1.16/29 are unable to access each other. What can be the cause of this problem?
ans:
RIPv1 does not support discontiguous networks.

41. Refer to the exhibit. All routers are properly configured to use the EIGRP routing protocol with default settings, and the network is fully converged. Which statement correctly describes the path that the traffic will use from the 10.1.1.0/24 network to the 10.1.2.0/24 network?
ans:
The traffic will be load-balanced between A-B-D and A-C-D.

42. A network administrator has enabled RIP on routers B and C in the network diagram. Which of the following commands will prevent RIP updates from being sent to Router A?
ans:
B(config)# router rip
B(config-router)# passive-interface S0/0

43. Which two statements are correct about the split horizon with poison reverse method of routing loop prevention? (Choose two.)
ans:
It assigns a value that represents an infinite metric to the poisoned route.
It sends back the poisoned route update to the same interface from where it was received.

44. Refer to the exhibit. The 10.4.0.0 network fails. What mechanism prevents R2 from receiving false update information regarding the 10.4.0.0 network?
ans:
split horizon

45. Refer to the exhibit. How many routes are ultimate routes?
ans:
5

46. Refer to the exhibit. Which two statements are true based on the exhibited output? (Choose two.)
ans:
All routes are stable.
The show ip eigrp topology command has been run on R1.

47. A router has learned two equal cost paths to a remote network via the EIGRP and RIP protocols. Both protocols are using their default configurations. Which path to the remote network will be installed in the routing table?
ans:
the path learned via EIGRP

48. Which two statements are true about the EIGRP successor route? (Choose two.)
ans:
It may be backed up by a feasible successor route.
It is used by EIGRP to forward traffic to the destination.

49. Refer to the exhibit. The output of the show ip route command for router R1 is displayed. What action will the router take for a packet that is destined for 192.168.1.5?
ans:
It will forward the packet to the default gateway.

50. Refer to the exhibit. The hosts that are connected to R2 are unable to ping the hosts that are connected to R1. How can this problem be resolved?
ans:
Configure the R2 router interfaces for area 0.

51. In a lab test environment, a router has learned about network 172.16.1.0 through four different dynamic routing processes. Which route will be used to reach this network?
ans:
D 172.16.1.0/24 [90/2195456] via 192.168.200.1, 00:00:09, Serial0/0/0

52. Refer to the exhibit. Which two facts can be derived from this output? (Choose two.)
ans:
Three network devices are directly connected to Router2.
The serial interface between Router2 and Router3 is up.

53. How does route poisoning prevent routing loops?
ans:
Failed routes are advertised with a metric of infinity.

54. Refer to the exhibit. A network administrator wants to reduce the size of the routing table of R1. Which partial routing table entry in R1 represents the route summary for R2, without including any additional subnets?
ans:
10.0.0.0/22 is subnetted, 1 subnets
D 10.5.0.0[90/205901] via 192.168.1.2, S0/0/0

55. Refer to the exhibit. Packets destined to which two networks will require the router to perform a recursive lookup? (Choose two.)
ans:
10.0.0.0/8
192.168.2.0/24

56. Refer to the exhibit. Although R2 is configured correctly, host A is unable to access the Internet. What are two static routes that can be configured on R1, either of which would enable Internet connectivity for host A? (Choose two.)
ans:
ip route 0.0.0.0 0.0.0.0 Fa0/1
ip route 0.0.0.0 0.0.0.0 10.1.1.2

57. Refer to the exhibit. Which router is advertising subnet 172.16.1.32/28?
ans:
Router4

58. Which statement is true about the metrics used by routing protocols?
ans:
A metric is a value used by a particular routing protocol to compare paths to remote networks.

59. Refer to the exhibit. Which two components are required to complete the configuration? (Choose two.)
ans:
a DTE device
a V.35 cable

Your contribution will help keep this site updated!

Expect minimum percentage: 90.2%

1. Which of the following are primary functions of a router? (Choose two.)
ans:
packet switching
path selection

2. Refer to the exhibit. Pings are failing between HostA and HostB. The network administrator discovers that Router1 does not have a route to the 172.16.0.0 network. Assuming Router2 is configured correctly, which two static routes could be configured on Router1 to enable Host A to reach network 172.16.0.0? (Choose two.)
ans:
ip route 172.16.0.0 255.255.0.0 S0/0
ip route 172.16.0.0 255.255.0.0 192.168.0.2

3. Refer to exhibit. Given the topology shown in the exhibit, what three commands are needed to configure EIGRP on the Paris router? (Choose three.)
ans:
Paris(config)# router eigrp 100
Paris(config-router)# network 192.168.7.0
Paris(config-router)# network 192.168.8.0

4. Refer to the exhibit. A packet enters Router1 with a destination IP of 172.16.28.121. Which routing table entry will be used to forward this packet to the destination address?
ans:
172.16.16.0/20 [1/0] via 192.168.0.17

5. Refer to the exhibit. Which statement is true concerning the routing configuration?
ans:
Packets routed to the R2 Fast Ethernet interface require two routing table lookups.

6. Refer to the exhibit. Packets destined to which two networks will require the router to perform a recursive lookup? (Choose two.)
ans:
10.0.0.0/8
192.168.2.0/24

7. Refer to the exhibit. The network is using the RIPv2 routing protocol. If network 10.0.0.0 goes down, what mechanism will prevent Router1 from advertising false routing information back to Router2?
ans:
split horizon

8. Refer to the exhibit. When troubleshooting a network, it is important to interpret the output of various router commands. On the basis of the exhibit, which three statements are true? (Choose three.)
ans:
The missing information for Blank 1 is the command show ip route.
The missing information for Blank 2 is the number 120.
The missing information for Blank 3 is the letter C.

9. The network administrator configures the router with the ip route 172.16.1.0 255.255.255.0 172.16.2.2 command. How will this route appear in the routing table?
ans:
S 172.16.1.0 [1/0] via 172.16.2.2

10. Refer to the exhibit. Which three statements are true of the routing table for Router1? (Choose three.)
ans:
The AD of EIGRP routes has been manually changed to a value other than the default value.
Router1 is running both the EIGRP and OSPF routing process.
No default route has been configured.

11. The network shown in the diagram is having problems routing traffic. It is suspected that the problem is with the addressing scheme. What is the problem with the addressing used in the topology?
ans:
The subnetwork configured on the serial link between Router1 and Router2 overlaps with the subnetwork assigned to Ethernet0 of Router3.

12. What is the purpose of the TTL field within an IP packet header?
ans:
limits the period of time or number of hops a packet can traverse through the network before it should be discarded

13. Refer to the exhibit. When the show cdp neighbors command is issued from router C, which devices will be displayed in the output?
ans:
B, D

14. Refer to the exhibit. The network administrator issues the command no ip classless on Router1. What forwarding action will take place on a packet that is received by Router1 and is destined for host 192.168.0.26?
ans:
The packet will be dropped.

15. Refer to the exhibit. The network is running the RIP routing protocol. Network 10.0.0.0 goes down. Which statement is true regarding how the routers in this topology will respond to this event?
ans:
Router5 will send Router4 a triggered update with a metric of 16 for network 10.0.0.0.

16. The Suffolk router is directly connected to the networks shown in the graphic and has a default route that points to the Richmond router. All interfaces are active and properly addressed. However, when the workstation on network 172.29.5.0/24 sends a packet to destination address 172.29.198.5, it is discarded by the Suffolk router. What can be a reason for this result?
ans:
The route was ignored if the Richmond router did not include the 172.29.198.0/24 network in its routing updates.

17. Refer to the exhibit. Which two statements are true based on the exhibited output? (Choose two.)
ans:
The serial interface between the two routers is down.
The show ip eigrp topology command has been run on R1.

18. Refer to the exhibit. All routers in the network are running RIPv2 and EIGRP with default routing protocol settings and have interfaces configured with the bandwidths that are shown in the exhibit. Which protocol will be used and how will traffic between the Router1 LAN and Router5 LAN be routed through the network?
ans:
RIPv2 traffic will use the path Router1, Router2, Router5 because it has the least hops.

19. Refer to the exhibit. The network administrator is testing network connectivity by issuing the tracert command from host A to host B. Given the exhibited output on host A, what are two possible routing table issues on the network? (Choose two.)
ans:
Router2 is missing a route to the 172.16.0.0 network
Router3 is missing a route to the 10.0.0.0 network

20. What are two switching functions of a router? (Choose two.)
ans:
The router encapsulates the packet in the appropriate data link frame type for the outgoing data link.
The router determines the exit interface after data encapsulation.

21. Refer to the exhibit. The routers in the exhibit are running the EIGRP routing protocol. What statement is true regarding how packets will travel from the 172.16.1.0/16 network to the 192.168.200.0/24 network?
ans:
The router installs all the equal cost paths in the routing table and performs equal cost load balancing to send packets out multiple exit interfaces.

22. When presented with multiple valid routes to a destination, what criteria does a router use to determine which routes to add to the routing table?
ans:
The router first selects routes with the lowest administrative distance. The resulting routes are then prioritized by metric and the routes with the best metric are added to the routing table.

23. Which two router component and operation pair are correctly described? (Choose two.)
ans:
NVRAM – stores the configuration file
POST – runs diagnostics on hardware modules

24. Refer to the exhibit. What are the effects of the exhibited commands on the router?
ans:
Only the enable password is encrypted.

25. Refer to the exhibit. Routers 1 and 2 are directly connected over a serial link. Pings are failing between the two routers. What change by the administrator will correct the problem?
ans:
Change the IP address on Serial 0/1/0 on router 2 to 192.168.0.1/30.

26. Which three statements about routing protocols are true? (Choose three.)
ans:
EIGRP supports unequal cost load balancing.
OSPF elects designated routers on multiaccess links.
RIP does not advertise a route beyond a hop count of 15.

27. What is the first step OSPF and IS-IS routers take in building a shortest path first database?
ans:
send hello to discover neighbors and form adjacencies

28. What are two tasks that must be completed before two routers can use OSPF to form a neighbor adjacency? (Choose two.)
ans:
The routers must agree on the network type.
The routers must use the same dead interval.

29. Refer to the exhibit. R1 knows two routes, Path A and Path B, to the Ethernet network attached to R3. R1 learned Path A to network 10.2.0.0/16 from a static route and Path B to network 10.2.0.0/16 from EIGRP. Which route will R1 install in its routing table?
ans:
The route via Path A is installed because the static route has the lowest administrative distance to network 10.2.0.0/16.

30. Refer to the exhibit. A new PC was deployed in the Sales network. It was given the host address of 192.168.10.31 with a default gateway of 192.168.10.17. The PC is not communicating with the network properly. What is the cause?
ans:
192.168.10.31 is the broadcast address for this subnet.

31. Refer to the exhibit. Which two routes are child routes? (Choose two.)
ans:
10.0.0.0
10.1.2.0

32. Refer to the exhibit. The results of the show ip route command are displayed in the graphic for Router R2. Which route will be selected for a packet with a destination address of 10.1.4.1?
ans:
route to 10.1.0.0/23

33. Refer to the routing table shown in the exhibit. What is the meaning of the highlighted value 192?
ans:
It is the metric, which is cost.

34. Refer to the exhibit. All router interfaces are configured with an IP address and are operational. If no routing protocols or static routes are configured, what information will be included in the show ip route command output for router A?
ans:
Routes to networks 192.168.1.0/24, 192.168.2.0/24, and 192.168.3.0/24 will be in the routing table.

35. A router has learned about a network through static and dynamic routing processes. Which route will be used to reach network 192.168.168.0?
ans:
S 192.168.168.0/24 [1/0] via 192.168.200.1

36. What does RIP use to reduce convergence time in a larger network?
ans:
It uses triggered updates to announce network changes if they happen in between the periodic updates.

37. Which three statements are true regarding the encapsulation and de-encapsulation of packets when traveling through a router? (Choose three.)
ans:
The router modifies the TTL field, decrementing it by one.
The router maintains the same source and destination IP.
The router changes the source physical address to the physical address of the exit interface.

38. A network administrator has enabled RIP on routers B and C in the network diagram. Which of the following commands will prevent RIP updates from being sent to Router A?
ans:
B(config)# router rip
B(config-router)# passive-interface S0/0

39. Using default settings, what is the next step in the router boot sequence after the IOS loads from flash?
ans:
Locate and load the startup-config file from NVRAM.

40. Refer to exhibit. A company network engineer enters the following commands in the routers:

R1(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.2
R2(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.1

When the engineer enters the show ip route command on R1, the routing table does not display the static route to the 10.1.1.0 network. All R1 and R2 interfaces are correctly addressed per the graphic. What is a logical next step that the engineer could take in order to make the static route display in the routing table in R1?
ans:
Enable the R1 and R2 serial interfaces.

41. What should be considered when troubleshooting a problem with the establishment of neighbor relationships between OSPF routers? (Choose two.)
ans:
OSPF interval timers mismatch
interface network type mismatch

42. Refer to the exhibit. What summary address can Router2 advertise to Router1 to reach the three networks on Routers 3, 4, and 5 without advertising any public address space or overlapping the networks on Router1?
ans:
172.16.0.0/13

43. What command would the network administrator apply to a router that is running OSPF to advertise the entire range of addresses included in 172.16.0.0/19 in area 0?
ans:
R1(config-router)# network 172.16.0.0 0.0.31.255 area 0

44. Refer to the exhibit. Which path will traffic from the 172.16.1.0/24 network take to get to the 10.0.0.0/24 network?
ans:
It will load balance the traffic between ADC and ABC

45. What is the function of the OSPF LSU packet?
ans:
used to announce new OSPF information and to reply to certain types of requests

46. Which statement is true regarding routing metrics?
ans:
Routers compare metrics to determine the best route.

47. Refer to the exhibit. A network administrator is trying to determine why router JAX has no OSPF routes in its routing table. All routers are configured for OSPF area 0. From the JAX router, the administrator is able to ping its connected interfaces and the Fa0/1 interface of the ORL router but no other router interfaces. What is a logical step that the network administrator should take to troubleshoot the problem?
ans”;
Use show and debug commands to determine if hellos are propagating.

48. Which two statements are correct about the split horizon with poison reverse method of routing loop prevention? (Choose two.)
ans:
It assigns a value that represents an infinite metric to the poisoned route.
It sends back the poisoned route update to the same interface from where it was received.

49.
Which three statements describe the operation of routing with EIGRP? (Choose three.)
ans:
As new neighbors are discovered, entries are placed in a neighbor table.
If hello packets are not received within the hold time, DUAL must recalculate the topology.

50. Which two statements are true regarding link-state routing protocols? (Choose two.)
ans:
They are aware of the complete network topology.
They offer rapid convergence times in large networks.

51.
What are three features of CDP? (Choose three.)
ans:
tests Layer 2 connectivity
enabled by default on each interface
provides information on directly connected devices that have CDP enabled

52. Refer to the exhibit. Hosts on the BOS Fa0/0 LAN are able to ping the Fa0/1 interface on the JAX router and all interfaces on the BOS and ORL routers. Why would hosts from the 10.0.0.0/24 network not be able to ping hosts on the Fa0/0 LAN of the JAX router?
ans:
The JAX router needs the network 192.168.3.0 0.0.0.255 area 0 command.

53. Which of the following are required when adding a network to the OSPF routing process configuration? (Choose three.)
ans:
network address
wildcard mask
area ID

54. Refer to the exhibit. What is the most efficient summarization of the routes attached to router R1?
ans:
198.18.48.0/21

55. A network administrator has configured a default route on Router_A but it is not being shared with adjacent Router_B and the other routers in the OSPF area. Which command will save the administrator the time and trouble of configuring this default route on Router_B and all of the other routers in the OSPF area?
ans:
Router_A(config-router)# ip ospf update-default

56. What can be determined from the output shown in the exhibit? (Choose two.)
ans:
Montgomery has Layer 2 connectivity with Cumberland.
Brant, Fisherman, and Potomac are directly connected to Montgomery.

57. Refer to the exhibit. What will happen if interface Serial0/0/1 goes down on Router1?
ans:
DUAL will query neighbors for a route to network 192.168.1.0.

58. Which of the following could describe the devices labeled “?” in the graphic? (Choose three.)
ans:
DCE
CSU/DSU
modem

59. Refer to the exhibit. How many routes are both level 1 and qualify for use as an ultimate route?
ans:
2

Your contribution will help keep this site updated!

Expect minimum percentage: 97.4%

1. Which algorithm is run by link-state routing protocols to calculate the shortest path to destination networks?
ans:
Dijkstra

2. What feature do modern link-state protocols provide to minimize processing and memory requirements?
ans:
splitting routing topologies into smaller areas

3. What is the final step in the link state routing process?
ans:
SPF computes best path to each destination network

4. Refer to the exhibit. Which statement correctly describes the path traffic would take from the 10.0.0.0/24 network to the 192.168.1.0/24 network if a link-state routing protocol was in use?
ans:
BOS -> ORL -> JAX -> ATL because this path is the lowest cost

5. Refer to the exhibit. What kind of information would be seen in an LSP sent from router JAX to router ATL?
ans:
cost of the link

6. Refer to the exhibit. When Router D is configured to use a link-state routing protocol and is added to the network, what is the first thing that it does to begin learning the network topology?
ans:
It learns about its directly connected networks when its interfaces reach the up state.

7. What two statements correctly describe the link state routing process? (Choose two.)
ans:
all routers in the area have link state databases
each router in the area floods LSPs to all neighbors

8. What speeds up convergence in a network using link-state routing?
ans:
updates triggered by network changes

9. Why is it difficult for routing loops to occur in networks that use link-state routing?
ans:
Each router builds a complete and synchronized view of the network.

10. What are two advantages of using a link-state routing protocol instead of a distance vector routing protocol? (Choose two.)
ans:
Each router independently determines the route to each network.
After the inital LSP flooding, they generally require less bandwidth to communicate changes in a topology.

11. To achieve network convergence, what three steps does each link state router take? (Choose three.)
ans:
build a Link State Packet (LSP) containing the state of each directly connected link
flood the LSP to all neighbors, who then store all LSPs received in a database
construct a complete map of the topology and compute the best path to each destination network

12. What two events will cause a link state router to send LSPs to all neighbors? (Choose two.)
ans:
whenever the network topology changes
upon initial startup of router or routing protocol

13. Which database or table must be identical on all link-state routers within an area in order to construct an accurate SPF tree?
ans:
link-state database

14. Which two routing protocols use Dijkstra’s shortest path first algorithm? (Choose two.)
ans:
IS-IS
OSPF

15. When are link-state packets sent to neighbors?
ans:
when a link goes up or down

16. Refer to the exhibit. What does JAX do with link-state packets from ORL?
ans:
sends out the individual link-state packets out the interface connected to BOS

17. A new network administrator is given the task of selecting an appropriate dynamic routing protocol for a software development company. The company has over 100 routers, uses CIDR and VLSM, requires fast convergence, and uses both Cisco and non-Cisco equipment. Which routing protocol is appropriate for this company?
ans:
OSPF

18. What action does a link-state router take immediately upon receipt of an LSP from a neighboring router?
ans:
floods the LSP to neighbors

19. Refer to the exhibit. If all routers and interfaces are configured to use a link-state routing protocol, from which routers will router D receive hello packets?
ans:
B and C

Your contribution will help keep this site updated!

Expect minimum percentage: 100%

1. On a router running EIGRP, what database would maintain a list of feasible successors?
ans:
topology table

2. Refer to the exhibit. This is the debug output from 2 directly connected EIGRP routers. They are not forming an adjacency. What is the cause?
ans:
they have different autonomous-system numbers

3. Refer to the exhibit. Which command will advertise the 192.168.1.64/30 network but not the 192.168.1.32 network on router A?
ans:
network 192.168.1.64 0.0.0.3

4. What two actions will the EIGRP DUAL FSM take if a link to a network goes down? (Choose two.)
ans:
query neighbors for a new route
search topology table for a feasible successor

5. Refer to the exhibit. What is indicated by the P at the beginning of the topology entry?
ans:
the route is in a stable state

6. In which of the following tables does the EIGRP DUAL algorithm store the primary route to a destination? (Choose two.)
ans:
routing
topology

7. What information is maintained in the EIGRP topology database for a destination route? (Choose two.)
ans:
the feasible distance of the route
the route cost as advertised by the neighboring router

8. Which of the following statements describes the bounded updates used by EIGRP?
ans:
Partial updates are sent only to routers that need the information.

9. Host 192.168.1.66 in the network illustrated is unable to ping host 192.168.1.130. How must EIGRP be configured to enable connectivity between the two hosts? (Choose two.)
ans:
R1(config-router)# no auto-summary
R2(config-router)# no auto-summary

10. Which two statements describe characteristics of EIGRP? (Choose two.)
ans:
EIGRP is a distance vector routing protocol.
EIGRP supports classless routing and VLSM.

11. Refer to the exhibit. Based on the output of show ip eigrp neighbors, what are two possible problems with adjacencies between Router1 and Router2? (Choose two.)
ans:
The routers are configured with different EIGRP process IDs.
The serial interfaces for both routers are in different networks.

12. Refer to the exhibit. In the topology table, what do the numbers 3011840 and 3128695 represent?
ans:
the total metric for that network as advertised by the EIGRP neighbor

13. Refer to the exhibit. EIGRP is the only routing protocol enabled on this network. No static routes are configured on this router. What can be concluded about network 198.18.1.0/24 from the exhibited output?
ans:
Packets that are destined for 198.18.1.0/24 will be forwarded to 198.18.10.6.

14. Refer to the exhibit. All interfaces have been configured with the bandwidths that are shown in the exhibit. Assuming that all routers are using a default configuration of EIGRP as their routing protocol, what path will packets take from the 172.16.1.0/16 network to the 192.168.200.0/24 network?
ans:
A,B,E

15. By default, which two metrics are used by EIGRP to determine the best path between networks?
ans:
delay
bandwidth

16. Which term defines a collection of networks under the administrative control of a single entity that presents a common routing policy to the Internet?
ans:
autonomous system

17. Refer to the exhibit. The company is using EIGRP with an autonomous system number of 10. Pings between hosts on networks that are connected to router A and those that are connected to router B are successful. However, users on the 192.168.3.0 network are unable to reach users on the 192.168.1.32 network. What is the most likely cause of this problem?
ans:
The routers are not configured in the same EIGRP routing domain.

18. In the command router eigrp 20, what is the purpose of the number 20?
ans:
identifies the autonomous system number this EIGRP process will advertise

19. The show ip eigrp topology command output on a router displays a successor route and a feasible successor route to network 192.168.1.0/24. In order to reduce processor utilization, what does EIGRP do when the primary route to this network fails?
ans:
The backup route to network 192.168.1.0/24 is installed in the routing table.

20. What administrative distance would a router assign to a default route in EIGRP that is learned from a source external to the autonomous system?
ans:
170

21. Refer to the exhibit. Network 192.168.0.0/28 goes down. What type of packet does Router2 immediately send to Router1 and Router3?
ans:
unicast update packets to 192.168.1.1 and 192.168.2.1

Your contribution will help keep this site updated!

Expect minimum percentage: 100%

1. Refer to the exhibit. The network administrator has discovered that packets destined for servers on the 172.16.254.0 network are being dropped by Router2. What command should the administrator issue to ensure that these packets are sent out the gateway of last resort, Serial 0/0/1?
ans:
ip classless

2. Refer to the exhibit. How many routes in this output qualify for use as ultimate routes?
ans:
7

3. The following entry is displayed in the routing table:

R 192.168.8.0/24 [120/2] via 192.168.4.1, 00:00:26, Serial0/0/1

What type of route is this?
ans:
a level 1 ultimate network route

4. Refer to the exhibit. The graphic contains partial contents of the routing table on router E. Router E is running version 12.3 of the IOS and is configured for default routing behavior. Router E receives a packet to forward. Which route in the routing table will be searched first and why?
ans:
172.16.0.0/25 because it is the first level 1 route

5. Refer to the exhibit. A packet destined for host 128.107.0.5/16 is processed by the JAX router. After finding the static route in the routing table that matches the destination network for this packet, what does the router do next?
ans:
performs a recursive lookup to find the exit interface used to forward the packet

6. A network is converged and the routing tables are complete. When a packet needs to be forwarded, what is the first criterion used to determine the best path in the routing table?
ans:
the route with the longest address and mask match to the destination

7. Refer to the exhibit. Router1 is running IOS version 12.2. What will the network administrator need to do so that packets for unknown child routes of 172.16.0.0/24 will not be dropped?
ans:
do nothing, ip classless is on by default

8. Refer to the exhibit. Router B receives a packet with a destination address of 10.16.1.97. What will router B do?
ans:
use the default route

9. Refer to the exhibit. What protocol was used to distribute the routing information for the network 172.16.1.4?
ans:
RIPv2

10. Refer to the exhibit. What subnet mask will Router1 apply to child routes of the 172.16.0.0/24 network?
ans:
255.255.255.0

11. A route to a destination network is learned from multiple routing protocols. What is used by a Cisco router to select the preferred route to the destination that will be installed in the routing table?
ans:
administrative distance

12. What occurs when no ip classless is implemented on the router?
ans:
The router will assume it has knowledge of all subnets in the network and will not search beyond child routes for a better match.

13. Refer to the exhibit. Router1 has been issued the ip classless command. What happens to packets destined to host 172.16.3.10?
ans:
forward out interface Serial0/0/1

14. Refer to the exhibit. With the ip classless command issued, what will router R2 do with a packet destined for host 172.16.4.234?
ans:
send packet out Serial 0/0/1

15. Refer to the exhibit. What parent network will automatically be included in the routing table when the three subnets are configured on Router1?
ans:
172.16.0.0/16

16. Refer to the exhibit. Which statement correctly describes this network?
ans:
There is at least one parent and one child route

17. Refer to the exhibit. What can be determined from this output?
ans:
All of the routes listed are network routes.

18. What determines if the router implements a classless route lookup process?
ans:
The command ip classless is enabled on the router.

Your contribution will help keep this site updated!

Expect minimum percentage: 100%

1. Refer to the exhibit. If all routers are running RIP version 2, why is there no route for the 192.168.1.32/27 network?
ans:
Rip version 2 will auto summarize routes by default.

2. What are two reasons to implement RIP version 2 rather than RIP version 1? (Choose two.)
ans:
RIP version 2 supports VLSM.
RIP version 2 supports routing update authentication.

3. Refer to the exhibit. RIPv1 is configured as the routing protocol for the network that is shown. The following commands are used on each router:
router rip
network 10.0.0.0
network 172.16.0.0
When this configuration is complete, users on the LAN of each router are unable to access the remote LANs. Why?
ans:
RIPv1 is unable to route to discontiguous subnets of a major network.

4. Refer to the exhibit. What effect will the commands that are shown have on RIP updates for Router1?
ans:
Only version 2 updates are sent to 224.0.0.9.

5. Refer to the exhibit. A technician needs to add a new loopback interface to test routing functionality and network design. The technician enters the following set of commands on the router:
Sanford(config)# interface loopback1
Sanford(config-if)# ip address 192.168.6.62 255.255.255.252
Why does the router respond with an error?
ans:
The network address for Loopback1 overlaps with an already configured interface address.

6. What is the maximum network diameter permitted by the default metric of RIPv2?
ans:
15 hops

7. Refer to the exhibit. All routers are running RIP version 2. JAX is configured to just advertise the 10.0.0.0/24 network. CHI is configured to advertise the 172.16.0.0/16 network. A network administrator enters the commands shown in the exhibit. What changes will occur in this network?
ans:
The CHI router will install a route to the 192.168.0.0/16 network in its routing table.

8. Refer to the exhibit. What can be concluded from the output shown in the exhibit?
ans:
The no auto-summary has not been configured on this router.

9. Refer to the exhibit. All routers are running RIPv1. What changes will occur in the routing table of router B if a loopback interface with an address of 10.16.1.129/27 is configured on router B?
ans:
A connected route to the 10.16.1.128/27 network is added.

10. How are RIP v1 and RIP v2 similar to one another? (Choose three.)
ans:
They both use hop count as a metric.
They both have the same metric value for infinite distance.
They both use split horizon to prevent routing loops.

11. RIPv2 is the configured routing protocol on the routers in a network. The command Router(config-router)# no version 2 is entered on the routers. What effect does entering this command have on routing updates?
ans:
Version 1 and 2 updates will be received and the version 2 updates will not be sent.

12. A network administrator installed four new routers that are running RIPv2. Router1 is a boundary router in the RIPv2 network and has a default route configured. Once the network has converged, the network administrator enters Router1(config-router)# default-information originate on Router1. How will this affect the network?
ans:
propagates the default route to all routers in the network

13. Refer to the exhibit. The exhibited network contains a mixture of Cisco and non-Cisco routers. The command debug ip rip was entered on the JAX router. All routers are running the same version of RIP. Router CHI and Router ORL are not able to reach the 192.168.1.16/28 network. What is a possible solution to this problem?
ans:
Configure RIPv2 on routers.

14. Refer to the exhibit. Which command on which router will allow Router1 to learn about the 192.168.0.0/20 network?
ans:
Router2(config-router)# version 2

15. A network administrator has been told that the company IP address infrastructure must adhere to RFC 1918. What three IP address ranges from RFC 1918 could the administrator use on the network? (Choose three.)
ans:
10.0.0.0/8
172.16.0.0/12
192.168.0.0/16

16. Refer to the exhibit. Routers East and West are configured using RIPv1. Both routers are sending updates about their directly connected routes. The East router can ping the West router serial interface and West can ping the serial interface of East. However, neither router has dynamically learned routes from the other. What is most likely the problem?
ans:
VLSM is not supported by RIPv1.

17. Refer to the exhibit. Which command will allow Router2 to learn about the 192.168.16.0/28 network?
ans:
Router1(config-router)# network 192.168.16.0

18. What field was added to the RIP message header by RFC 1723 to add support for VLSM and CIDR?
ans:
subnet mask

19. What are two functions of the network command used when configuring routing protocols? (Choose two.)
ans:
identifies which networks will be included in the routing updates
determines which interfaces can send and receive routing updates

Your contribution will help keep this site updated!

Expect minimum percentage: 100%

1. Refer to the exhibit. The network administrator wants to create a subnet for the point-to-point connection between the two routers. Which subnetwork mask would provide enough addresses for the point-to-point link with the least number of wasted addresses?
ans:
255.255.255.252

2. An additional subnet is required for a new Ethernet link between Router1 and Router2 as shown in the diagram. Which of the following subnet addresses can be configured in this network to provide a maximum of 14 useable addresses for this link while wasting the fewest addresses?
ans:
192.1.1.224/28

3. Refer to the exhibit. A network engineer is summarizing the two groups of routes on router R1 shown in the exhibit. Which summarization will work for all the subnets?
ans:
192.168.0.0/21

4. What is a supernet?
ans:
a summarization of serveral IP classful networks into one IP address range

5. In the network shown in the graphic, three bits were borrowed from the host portion of a Class C address. How many valid host addresses will be unused on the three point-to-point links combined if VLSM is not used?
ans:
84

6. What does VLSM allow a network administrator to do?
ans:
utilize multiple subnet masks in the same IP address space

7. Refer to the exhibit. The network administrator wants to minimize the number of entries in Router1’s routing table. What should the administrator implement on the network?
ans:
CIDR

8. Refer to the exhibit. A network technician enters the static route in R1 needed to reach network 10.1.1.0/24. A ping from the S0/0/0 interface on R1 to host B fails. The technician begins testing the network and has the following results:
1. pings from R1 to the S0/0/0 interface on R2….successful
2. pings from R1 to the Fa0/0 interface on R2….successful
3. pings from host B to hosts on the 10.1.1.0/24 network….successful
4. pings from host B to the Fa0/0 interface on R2….successful
5. pings from R2 to host B….successful.
What is the likely cause of the failure of the ping from R1 to host B?
ans:
The default gateway on host B is not correctly set.

9. Which three interior routing protocols support VLSM? (Choose three.)
ans:
OSPF
RIP v2
EIGRP

10. Refer to the exhibit. A network administrator needs to create two subnetworks from 10.0.0.0/8 for a router running RIPv2. The Admin subnet requires 120 hosts and the Sales subnet requires 58 hosts. The network administrator assigned 10.0.1.128/25 to the Admin subnet. The Sales subnet is given 10.0.1.192/26. What will be the result of this addressing scheme?
ans:
The subnets overlap and will be rejected by the router.

11. Which of the following are contained in the routing updates of classless routing protocols? (Choose two.)
ans:
32-bit address
subnet mask

12. A Class C address has been assigned for use in the network shown in the graphic. Using VLSM, which bit mask should be used to provide for the number of host addresses required on Router A, while wasting the fewest addresses?
ans:
/27

13. Refer to the exhibit. The number of required host addresses for each subnet in a network is listed in the exhibit. This number includes the host address requirements for all router ports and hosts on that subnet. After all device and router port address assignments are determined, what will be the total number of unused host addresses available?
ans:
29

14. What two advantages does CIDR provide to a network? (Choose two.)
ans:
reduced routing table size
reduced routing update traffic

15. A network administrator is tasked with dividing up a class C network among the QA, Sales, and Administration departments. The QA department is made up of 10 people, the Sales is made up of 28 people, and the Administration has 6. Which two subnets masks adequately address the QA and Sales departments? (Choose two.)
ans:
255.255.255.224 for Sales
255.255.255.240 for QA

16. Refer to the exhibit. In the network that is shown, the router interfaces are assigned the first address in each subnet. Which IP address would be usable for a host on one of the LANs in this network?
ans:
192.168.2.130/25

17. Refer to the exhibit. Which address is a broadcast address for one of the subnets that are shown in the exhibit?
ans:
192.168.4.15/29

18. Refer to the exhibit. What subnet mask will be applied by router B when it receives a RIPv1 update for the network 172.16.1.0?
ans:
24

19. Which of the following problems does VLSM help to alleviate?
ans:
the shortage of IP addresses

20. A router has a summary route to network 192.168.32.0/20 installed in its routing table. What range of networks are summarized by this route?
ans:
192.168.32.0 – 192.168.47.0/24

Your contribution will help keep this site updated!

Expect minimum percentage: 94.9%

1. Refer to the exhibit. The Ethernet interface on Router2 goes down and the administrator notices that the route is still valid in the routing table of Router1. How much longer will it take for Router1 to mark the route invalid by setting the metric to 16?
ans:
155 seconds

2. Refer to the exhibit. Router1 and Router2 are running the RIPv1 protocol. The network administrator configures the command network 10.1.0.0 on Router1. What network will Router1 advertise to Router2?
ans:
10.0.0.0/8

3. Refer to the exhibit. Router1 is running RIPv1. What command was entered into Router1 to configure the gateway of last resort?
ans:
ip route 0.0.0.0 0.0.0.0 S0/0/1

4. Refer to the exhibit. All routers that are shown are running the RIP routing protocol. All unknown IP traffic must be forwarded to the ISP. What router or set of routers are recommended to have both a default route and the default-information originate command issued to implement this forwarding policy?
ans:
only the gateway router

5. Refer to the exhibit. All routers are configured with valid interface addresses in the indicated networks and are running RIPv1. The network is converged. Which routes are present in the routing tables?
ans:
All routers have all /30 routes. Routers B and D also have some of the /24 routes in their routing table.

6. Refer to the exhibit. A network consists of multiple routers. What can be verified when the show ip protocols command is issued on one of the routers in the network?
ans:
routing protocol configuration in use for IP on this router

7. Which two statements are true regarding the characteristics of RIPv1? (Choose two).
ans:
It is a distance vector routing protocol.
The data portion of a RIP message is encapsulated into a UDP segment.

8. The following line was displayed in the output of the show ip route command.
R 192.168.3.0/24 [120/3] via 192.168.2.2, 00:00:30, Serial0/0
What is the value of the routing metric?
ans:
3

9. Which of the following is considered a limitation of RIP v1?
ans:
RIP v1 does not send subnet mask information in its updates.

10. What are three characteristics of the RIPv1 routing protocol? (Choose three.)
ans:
uses hop count as a metric
considers a metric of 16 as infinity
calculates metrics using the Bellman Ford algorithm

11. Refer to the exhibit. The network that is shown is running RIPv1. The 192.168.10.0/24 network was recently added and will only contain end users. What command or set of commands should be entered on Router1 to prevent RIPv1 updates from being sent to the end user devices on the new network while still allowing this new network to be advertised to other routers?
ans:
Router1(config-router)# passive-interface fastethernet 0/0

12. Refer to the exhibit. What can be concluded from the routing table output of router B?
ans:
The default-information originate command has been entered on A.

13. Which command will display RIP activity as it occurs on a router?
ans:
debug ip rip

14. Refer to the exhibit. All routers in the exhibit are running RIP v1. The network administrator issues the show ip route command on router A. What routes would appear in the routing table output if the network is converged? (Choose two).
ans:
R 192.168.2.0/24 [120/1]
R 10.10.1.0/24 [120/2]

15. What is the default update period in seconds for the RIP routing protocol?
ans:
30

16. Refer to the exhibit. What can be concluded from the output of the show ip route command?
ans:
There are two equal cost paths to network 172.16.100.128.

17. Refer to the exhibit. What can be concluded from the output of the show ip route command?
ans:
RouterB(config)# router rip
RouterB(config-router)# network 198.16.4.0
RouterB(config-router)# network 210.36.7.0
RouterB(config-router)# network 220.17.29.0

18. What will happen if an interface IP address is entered for the address portion of the network command in a RIPv1 configuration instead of a network address?
ans:
All interfaces in the same classful network as the configured address will be included in the RIPv1 routing process.

19. Which command or set of commands will stop the RIP routing process?
ans:
RouterB(config)# no router rip

Your contribution will help keep this site updated!

Expect minimum percentage: 100%

1. What does the RIP holddown timer do?
ans:
instructs routers to ignore updates, for a specified time or event, about possible inaccessible routes

2. What metric does the RIP routing protocol consider to be infinity?
ans:
16

3. What is a routing loop?
ans:
a condition where a packet is constantly transmitted within a series of routers without ever reaching its intended destination

4. Which two statements are true regarding the function of the RIPv1 routing updates? (Choose two).
ans:
updates are broadcast at regular intervals
broadcasts are sent to 255.255.255.255

5. Which of the following can exist in a distance vector network that has not converged? (Choose three.)
ans:
routing loops
inconsistent traffic forwarding
inconsistent routing table entries

6. Refer to the exhibit. What path will packets from the 192.168.1.0/24 network travel to reach the 10.0.0.0/8 network if RIP is the active routing protocol?
ans:
The path will be router A -> router D -> router E.

7. What is the purpose of the TTL field in the IP header?
ans:
limits the time or hops that a packet can traverse through the network before it should be discarded

8. Which two conditions are most likely to cause a routing loop? (Choose two.)
ans:
inconsistent routing tables
incorrectly configured static routes

9. Refer to the exhibit. If all routers are using RIP, how many rounds of updates will occur before all routers know all networks?
ans:
3

10. The graphic shows a network that is configured to use RIP routing protocol. Router2 detects that the link to Router1 has gone down. It then advertises the network for this link with a hop count metric of 16. Which routing loop prevention mechanism is in effect?
ans:
route poisoning

11. Refer to the exhibit. The routers in this network are running RIP. Router A has not received an update from Router B in over three minutes. How will Router A respond?
ans:
The Invalid timer will mark the route as unusable if an update has not been received in 180 seconds.

12. What actions will occur after RouterA loses connectivity to network 114.125.16.0? (Choose two.)
ans:
RouterB will include network 123.92.76.0 and 136.125.85.0 in its update to RouterA.
Router C will learn of the loss of connectivity to network 114.125.16.0 from RouterB.

13. Three routers running a distance-vector routing protocol lost all power, including the battery backups. When the routers reload, what will happen?
ans:
They will send updates that include only directly connected routes to their directly connected neighbors.

14. Which statement is true regarding cisco’s RIP_JITTER variable?
ans:
It prevents the synchronization of routing updates by subtracting a random length of time ranging from 0% to 15% of the specified interval time from the next routing update interval.

15. Which of the following methods does split horizon use to reduce incorrect routing information?
ans:
Information learned from one source is not distributed back to that source.

16. A network administrator is evaluating RIP versus EIGRP for a new network. The network will be sensitive to congestion and must respond quickly to topology changes. What are two good reasons to choose EIGRP instead of RIP in this case? (Choose two.)
ans:
EIGRP only updates affected neighbors.
EIGRP updates are partial.

17. Which two statements describe EIGRP? (Choose two.)
ans:
EIGRP sends triggered updates whenever there is a change in topology that influences the routing information.
EIGRP sends a partial routing table update, which includes just routes that have been changed.

18. Which three routing protocols are distance vector routing protocols? (Choose three).
ans:
RIPv1
EIGRP
RIPv2

19. Which of the following statements are correct about RIP?
ans:
will send out an update if there is a failure of a link

20. Which event will cause a triggered update?
ans:
a route is installed in the routing table

Your contribution will help keep this site updated!